Understanding Plumbing Basics is Crucial for Installing a Bathtub
Understanding Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
Just about everyone will have his or her own theory when it comes to Installing A Bathtub.
Setting up a bath tub isn't exactly rocket science, but it does require solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately tough task. If the old tub is readily available, the task can move rapidly; if you need to open up a wall surface to remove the old bathtub as well as place the brand-new tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the new one. Make sure you have certified yourself for the work and also are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is better to take into consideration using one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This write-up will assist you mount a brand-new bath tub in your washroom if you have currently gotten a brand-new bathtub and don't require to transform the plan of your previous water pipes.
Your devices and product list should comprise the following:
Getting ready for the Setup
First of all, the supporting structure provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is necessary to ensure that if the tap includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to stop strain on the bathtub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its final setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be quite bothersome because of the restricted gain access to that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipes. When the supply pipes have actually been gotten rid of, utilize the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, put the bath tub in the required position. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The next objective is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and also changing the feet on the tub until the level checks out degree.
To mount faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Switch on the water and inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Fill the bath tub as well as likewise inspect the overflow outlet and the normal outlet for leaks.
Finally, fix the bathroom paneling as defined in the producer's instruction manual. Tiling and securing around the bathtub must wait until the bath tub has been used a minimum of once as this will certainly resolve it into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the existent supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washing machines are in place between the faucet and the sink. Secure the tap in position with the manufacturer supplied backnut. Once the faucet is firmly in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind should be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can move enough to crack a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, leading to problems with dampness and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched paper or soft rope. Remember to constantly load the bath tub with water prior to securing, to permit the motion experienced when the tub is in usage. The sealer can break rather early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our post about Tools You Need to Install a New Bathtub . Thank you for taking a few minutes to read our blog post. For those who enjoyed our blog entry plz be sure to pass it around. We treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Top service? Contact. Report this page